MEB Test Bench
Teststände
The MEB Test Bench represents a model of a car electronics where all units can be seated and work the same as usual in cars.
Produktbeschreibung
Produktbeschreibung
This light version of test bench is mainly intended for supporting the development and testing of ICAS3 projects.
The advantage of this solution is that tests can be run without the need for an actual car. The MEB Test Bench is made of a lightweight aluminium construction. The structure holds a wired harness fixed in a wire duct, which is intended for the connection of ECUs to evaluate technologies and accessories.
Switches are located on the front panel of the test bench. The power supply and data terminals are accessible from the right side. The speakers are on both sides. This configuration provides potential extensibility to the test bench. We offer various accessories for this test bench.
It is also possible to extend the test bench using an RTL Enabler, which allows the user to remotely operate it from any location using a web browser.
Thanks to the flexibility of the mechanical design and a suitably designed wiring harness, the test state can be easily modified and extended. Custom modifications are also possible.
The advantage of this solution is that tests can be run without the need for an actual car. The MEB Test Bench is made of a lightweight aluminium construction. The structure holds a wired harness fixed in a wire duct, which is intended for the connection of ECUs to evaluate technologies and accessories.
Switches are located on the front panel of the test bench. The power supply and data terminals are accessible from the right side. The speakers are on both sides. This configuration provides potential extensibility to the test bench. We offer various accessories for this test bench.
It is also possible to extend the test bench using an RTL Enabler, which allows the user to remotely operate it from any location using a web browser.
Thanks to the flexibility of the mechanical design and a suitably designed wiring harness, the test state can be easily modified and extended. Custom modifications are also possible.
Hauptmerkmale
- Light and mobile test centre
- Online version registered to the backend
- Offline version
- Construction flexibility
- Possibility of extension with optional accessories (from a mechanical point of view)
- Possibility to connect other units and accessories (from a wiring point of view)
- CAN bus terminal
- ETH terminal
- Prepared for RTL Enabler
- Prepared for CANSim4 Simulator
- Prepared for MGB FrameGrabber
- Prepared for PDC Box
- Prepared for TraceBox
Bereit zum Anschluß
- In Car Application Server (ICAS1)
- In Car Application Server (ICAS3)
- Integrated control panel (ABT)
- Innovative Info Display (i.ID)
- Sensor-actuator module (SAM)
- Multi-function steering wheel (MFL)
- Start / Stop button
- USB-C HUB
- Electronic steering column lock (ELV)
- Kessy with antennas
- Door control module (TSG), locks
- LINDa (roof module)
- Air conditioning (AC)
- Online connectivity unit (OCU4)
- Speaker for OCU
- Transceiver box (Transc. Box)
- LTE antenna amplifier
- Koppelbox
- 4x loudspeakers (2 speakers included)
- On board diagnostic (OBD II)
- Rear view camera (RVC eCompact/eSmart)
- Top view camera eEntry (TVC)
- Cameras for top view eEntry
- Augmented-Reality-Head-Up-Display (AR-HUD)
- Smart Light
- Sound (AMP)
- Park Distance Control (PDC / PLA)
Zubehör
| Power supply | Switching power supply 0-16 V / 20 A |
| CANSim4 | Simulation of clamp states, speed, RPM, etc. |
| MGB FrameGrabber | Video capture of i.ID, ABT, etc. |
| RTL Enabler | Extends test bench to remotely operate it using a web browser |
| PDC Box | Compact, lightweight, aluminium box for PDC unit and sensors |
| TraceBox | Modular solution for tracing and data logging |
| MSG cable harness | Cable harness for connection of the motor control unit |
| RVC / TVC cable harness | Cable hanress for connection of RVC / TVC |
| PDC / PLA cable harness | Cable harness for connection of PDC / PLA |
| Sound box or cable harness for AMP | According to customer requirements |
| ABT holder | Aluminium panel for retrofitting |
| MFL holder | Holder for multifunction steering wheel on table (not intended for fixed mounting on the test bench) |
| LINDa holder | Holder for retrofitting the LINDa module |
| USB-C HUB holder | Holder for retrofitting the USB-C HUB |
| Antenna cables | Specific lengths |
| Antenna holders | Panel for retrofitting on the test bench |
| Other accessories | Available upon demand |
Technische Daten
| Unterstützte Plattformen | MEB |
| Hauptverwendung | Entwicklung und Validierung ICAS3 |
| Stecker | CAN, LIN, Ethernet, UART (RS232), OBD II |
| Stromversorgung | 12 V – 15 V |
| Betriebstemperatur | Benutzung nur unter Laborbedingungen |
| Abmessungen (B x T x H) | 400 x 350 x 350 mm (einschließlich Stecker, Bedienelemente und Bauteile auf der DIN Leiste) |
| Gewicht ohne Zubehör | 8,75 kg |
Stažení dokumentů.
Stažení dokumentů je umožněno pouze registrovaným uživatelům. Máte-li svůj účet pak je nutné se přihlásit.
Kontaktieren Sie uns - wir melden uns bei Ihnen!
Kontaktformular
2024 2019 © Digiteq Automotive s.r.o. Durch das Nutzen dieser Webseiten geben Sie Ihr Einverständnis damit, dass Cookie-Dateien verwendet werden.
Webseitenkreierung Freely Agency & H1.cz
Webseitenkreierung Freely Agency & H1.cz