MQB37W Test Bench
MQB37W Test Bench
Test benchesThe MQB37W Test Bench represents a model of a car electronics where all units can be seated and work the same as usual in cars.
The MQB37W Test Bench is mainly intended for supporting the development and testing of MIB3 projects.
The advantage of this solution is that tests can be run without the need for an actual car. The MQB37W Test Bench is made of a lightweight aluminium construction. The structure holds a wired harness fixed in a wire duct, which is intended for the connection of ECUs to evaluate technologies and accessories.
The front side of the test bench offers a place for the installation of ABT, SMLS, KI / FPK and other hardware. Additional units can be installed on the sides of the test bench, where data buses and sockets are located. The power and data terminals are located on the back side. This provides extensibility to the test bench. We offer various accessories for this test bench.
Thanks to the flexibility of the mechanical design and a suitably designed wiring harness, the test state can be easily modified and extended. Custom modifications are also possible.
The MQB37W Test Bench can be made in an online (connected to the backend) or an offline version. The test bench can be extended using an RTL Enabler that allows the user to remotely operate it from any location using a web browser.
Key Features
- Light and mobile test centre
- Offline version
- Construction flexibility
- Possibility to connect other units and accessories (from a wiring point of view)
- Prepared for RTL Enabler
- Prepared for FrameGrabber 4
- Prepared for MGB FrameGrabber
- Prepared for TraceBox
- Online version registered to the backend
- Optional connection for headphones
- Possibility of extension with optional accessories (from a mechanical point of view)
- CAN bus terminal
- Prepared for CANSim4 Simulator
- Prepared for PDC Box
Readiness to Connection
- Gateway (GW)
- Integrated control panel (ABT)
- Body control module (BCM)
- Steering column switch module (SMLS)
- USB-C HUB
- Read coil
- Door control module (TSG), locks
- Direct access button (DIETa)
- Koppelbox
- Speaker for OCU
- 4x loudspeakers (2 speakers included)
- Rear view camera (RVC eCompact/eSmart)
- Cameras for top view eEntry
- Sound (AMP)
- Park Distance Control (PDC/PLA)
- Modular infotainment matrix (MIB3)
- Instrument cluster (IC/FPK)
- Multi-function steering wheel (MFL)
- Start / Stop button
- Electronic steering column lock (ELV)
- Kessy with antennas
- LINDa (roof module)
- Air conditioning (AC)
- Online connectivity unit (OCU3)
- Lights and vision control panel (LiSi)
- On board diagnostic (OBD II)
- Top view camera eEntry (TVC)
- Head-Up-Display (HUD)
- 3.5 mm jack connector
Accessories
| Power supply | Switching power supply 0-16 V / 20 A |
| CANSim4 | Simulation of clamp states, speed, RPM, etc. |
| FrameGrabber 4 | A powerful video-capturing solution for multiple video streams in parallel e.g. IC, FPK, ABT. |
| MGB FrameGrabber | Video capture of IC / FPK, ABT, etc. |
| RTL Enabler | Extends test bench to remotely operate it using a web browser |
| PDC Box | Compact, lightweight, aluminium box for PDC unit and sensors |
| TraceBox | Modular solution for tracing and logging |
| MSG cable harness | Cable harness for connection of the motor control unit |
| RVC / TVC cable harness | Cable harness for connection of RVC / TVC |
| PDC / PLA cable harness | Cable harness for connection of PDC / PLA |
| Sound box or cable harness for AMP | According to customer requirements |
| ABT holder | Aluminium panel for retrofitting |
| IC / FPK holder | Retrofit kit |
| SMLS holder | Aluminium steering wheel module holder (SMLS) |
| LiSi holder | Plastic holder for lights and vision control panel (LiSi) |
| MFL holder | Holder for multi-function steering wheel to on table (not for fixed mounting on the test bench) |
| LINDa holder | Holder for retrofitting the LINDa module |
| Antenna cables | Specific lengths |
| Antenna holders | Panel for retrofitting on the test bench |
| USB-C HUB holder | Holder for USB-C HUB |
| Other accessories | Available upon demand |
Technical Parameters
| Supported platform | MQB37W |
| Main purpose | Development and validation of MIB3 |
| Connections | CAN, LIN, Ethernet, UART (RS232), OBD II |
| Power supply | 12 V to 15 V |
| Operating temperature | For use in laboratory conditions only |
| Dimensions (W x D x H) | 444 x 590 x 415 mm (including speakers, brackets and DIN rail parts) |
| Weight without accessories | 13.8 kg |