MQB37W Testwürfel
Teststände
The MQB37W Test Bench represents a model of a car electronics where all units can be seated and work the same as usual in cars.
Produktbeschreibung
Produktbeschreibung
The MQB37W Test Bench is mainly intended for supporting the development and testing of MIB3 projects.
The advantage of this solution is that tests can be run without the need for an actual car. The MQB37W Test Bench is made of a lightweight aluminium construction. The structure holds a wired harness fixed in a wire duct, which is intended for the connection of ECUs to evaluate technologies and accessories.
The front side of the test bench offers a place for the installation of ABT, SMLS, KI / FPK and other hardware. Additional units can be installed on the sides of the test bench, where data buses and sockets are located. The power and data terminals are located on the back side. This provides extensibility to the test bench. We offer various accessories for this test bench.
Thanks to the flexibility of the mechanical design and a suitably designed wiring harness, the test state can be easily modified and extended. Custom modifications are also possible.
The test bench can be extended using an RTL Enabler that allows the user to remotely operate it from any location using a web browser.
The advantage of this solution is that tests can be run without the need for an actual car. The MQB37W Test Bench is made of a lightweight aluminium construction. The structure holds a wired harness fixed in a wire duct, which is intended for the connection of ECUs to evaluate technologies and accessories.
The front side of the test bench offers a place for the installation of ABT, SMLS, KI / FPK and other hardware. Additional units can be installed on the sides of the test bench, where data buses and sockets are located. The power and data terminals are located on the back side. This provides extensibility to the test bench. We offer various accessories for this test bench.
Thanks to the flexibility of the mechanical design and a suitably designed wiring harness, the test state can be easily modified and extended. Custom modifications are also possible.
The test bench can be extended using an RTL Enabler that allows the user to remotely operate it from any location using a web browser.
Hauptmerkmale
- Light and mobile test centre
- Online version registered to the backend
- Offline version
- Optional connection for headphones
- Construction flexibility
- Possibility of extension with optional accessories (from a mechanical point of view)
- Possibility to connect other units and accessories (from a wiring point of view)
- CAN bus terminal
- Prepared for RTL Enabler
- Prepared for CANSim4
- Prepared for MGB FrameGrabber
- Prepared for PDC Box
- Prepared for TraceBox
Bereit zum Anschluß
- Gateway (GW)
- Modular infotainment matrix (MIB3)
- Integrated control panel (ABT)
- Instrument cluster (IC/FPK)
- Body control module (BCM)
- Multi-function steering wheel (MFL)
- Steering column switch module (SMLS)
- Start / Stop button
- USB-C HUB
- Electronic steering column lock (ELV)
- Read coil
- Kessy with antennas
- Door control module (TSG), locks
- LINDa (roof module)
- Direct access button (DIETa)
- Air conditioning (AC)
- Koppelbox
- Online connectivity unit (OCU3)
- Speaker for OCU
- Lights and vision control panel (LiSi)
- 4x loudspeakers (2 speakers included)
- On board diagnostic (OBD II)
- Rear view camera (RVC eCompact/eSmart)
- Top view camera eEntry (TVC)
- Cameras for top view eEntry
- Head-Up-Display (HUD)
- Sound (AMP)
- 3.5 mm jack connector
- Park Distance Control (PDC/PLA)
Zubehör
| Power supply | Switching power supply 0-16 V / 20 A |
| CANSim4 | Simulation of clamps state, speed, RPM etc. |
| MGB FrameGrabber | Video capture of IC / FPK, ABT etc. |
| RTL Enabler | Extender for possibility to operate test bench remotely using web browser |
| PDC Box | Compact, lightweight, aluminium box for PDC unit and sensors |
| TraceBox | Modular solution for tracing |
| MSG cable harness | Cable harness for connection of motor control unit |
| RVC / TVC cable harness | Cable harness for connection of RVC / TVC |
| PDC / PLA cable harness | Cable harness for connection of PDC / PLA |
| Sound box or cable harness for AMP | According to customer requirements |
| ABT holder | Aluminium panel for retrofitting |
| IC / FPK holder | Retrofit kit |
| SMLS holder | Aluminium steering wheel module holder (SMLS) |
| LiSi holder | Plastic holder for lights and vision control panel (LiSi) |
| MFL holder | Holder for multi-function steering wheel to the table (not for fixed mounting to the test bench) |
| LINDa holder | Holder for retrofitting the LINDa module |
| Antennas cables | Specific lengths |
| Antennas holders | Panel for retrofitting on the test bench |
| USB-C HUB holer | Holder for USB-C HUB |
| Other accessories | Available upon demand |
Technische Daten
| Unterstützte Plattformen | MQB37W |
| Hauptverwendung | Entwicklung und Validierung MIB3 |
| Stecker | CAN, LIN, Ethernet, UART (RS232), OBD II |
| Stromversorgung | 12 V – 15 V |
| Betriebstemperatur | Benutzung nur unter Laborbedingungen |
| Abmessungen (B x T x H) | 444 x 590 x 415 mm (einschließlich Stecker, Bedienelemente und Bauteile auf der DIN Leiste) |
| Gewicht ohne Zubehör | 13,8 kg |
Dokumentation
Dokumentation
Auf Anfrage bieten wir Ihnen eine individuelle Schulung und profesionelle Beratung zu diesem Produkt an. Für weitere Informationen kontaktieren Sie uns.
Produktblatt
Download
Stažení dokumentů.
Stažení dokumentů je umožněno pouze registrovaným uživatelům. Máte-li svůj účet pak je nutné se přihlásit.
Kontaktieren Sie uns - wir melden uns bei Ihnen!
Kontaktformular
2024 2019 © Digiteq Automotive s.r.o. Durch das Nutzen dieser Webseiten geben Sie Ihr Einverständnis damit, dass Cookie-Dateien verwendet werden.
Webseitenkreierung Freely Agency & H1.cz
Webseitenkreierung Freely Agency & H1.cz